Description :

Connols-Air Linear Slot Diffuser is mainly rated for supply but can be used as return unit or as combination unit as in the case with air-light fixtures. Our linear slot can be easily used with integrated ceiling system with appropriate installation accessory and special frame profile to match the ceiling design. Diffusers are available in 1 to 4 slots and in standard length of 1200 mm with end caps for plaster ceiling installation. For installation on inverted ceiling Tee bar, the diffuser will be constructed of standard 1194 mm length to suit 1200 X 600 mm accessible ceiling system. Standard length diffuser as such are available ex-stock in powder coated standard baked enamel RAL 9010. However longer length up to a maximum of 2400 mm can be custom-made when required. For length, longer than 2400 mm or continuous run linear slot diffuser, they may be formed by joining together 1800mm or 2400 mm diffusers with balance dimensions at each end. Alignment pins and/or bracket may be supplied to ensure straight joints. In addition to straight length diffuser, customised curve shape diffuser with or without acoustic plenum may be available as shown.

Supply air diffuser is supplied with acoustic plenum that is internally lined with fire retardant acoustic foam for better indoor air and sound quality. The acoustic plenum may be supplied with inlet butterfly damper (optional) so that fine airflow balancing with the damper may not increase the generated noise. Acoustic plenum is constructed of galvanised steel of standard length 1200 nominal dimension with one inlet spigot of size 150, 200 or 250 mm diameter. Longer acoustic plenum is available in length of 1800 and 2400 mm and may be provided with one or two inlet spigots depending on the air handling capacity of the linear slot diffuser.

High capacity single slot linear diffuser available in five slot widths, offers an attractive alternative to traditional multi-slot designs. A Vairtech slot diffuser is a building component used to deliver air to a room. These diffusers serve as a critical component in a heating, ventilation, and air conditioning (HVAC) system. Unlike traditional square or round diffusers, a slot diffuser features a long, narrow design.

Linear slot diffuser of similar number of slot may be used for matching return diffuser. The blade of the diffuser is used for minor airflow balancing. Acoustic plenum may be provided for better noise control.

For installation of diffuser on plaster ceiling great care must be considered during design phase of the project to ensure proper installation can be achieved during construction.

Features

• Frames and blades are constructed of corrosion resistance aluminium alloy and tempered to give rigidity
• Air Flow pattern setting is easy with dual function blade
• Flow pattern adjustable to give horizontal one or two-way throw or vertical throw for high ceiling installation
• Acoustics plenum internally insulated with fire retardant acoustic foam provide noise attenuation and hence ensure lower room noise.

How to Specify

AL20 [1] [2] [3] [4] [5] [6]

[1] Type:

• 50 - 1/2' slot
• 75 - 3/4' slot
• 10 - 1' slot

[2] Style:

1. Diffuser Only
2. Diffuser with pattern controller

[3] Number of Slots:

• 01-08 slots

[4] Mounting Style:

• B0 - T-Bar Lay-in -Diffuser Only
• E0 - Diffuser Only
• E1 - Hanger Bracket
• E2 - Standard Mounting Frame
• F0 - Screw holes in margin

[5] End Caps:

• E1 - One end
• E2 - Both ends
• 00 - None

[6] Length (inches)

• 12' min
• 999' max

[7] Finish

• CLR - Clear Anodized
• WHT - Bright White

• Extruded alumninum construction
• Three slot types: 50 (1/2' slot), 75 (3/4' slot), 10 (1' slot)
• One to eight slots wide for air volume of 10-350 cfm per foot
• Adjustable pattern controller
• Three margin styles: B, E, F
• 12' minimum length.
• Maximum one-piece length 72', lengths over 72' made in multiple units with pin splices for even continuous lengths (1/8' increments). 999' maximum continuous length.
• Available as diffuser-only or diffuser with pattern controller.

Margin Styles

B0 – T-Bar Lay-in Diffuser Only

Titus Continuous Slot Diffuser

Duct Width: A + 1/16
Overall Width: A + 7/8

E1

Overall Width: A + 3/4

Please see submittal drawing & hyperlink for details

E2

Overall Width: A + 3/4

Please see submittal drawing & hyperlink for details

E0 – Diffuser Only

Duct Width: A + 7/16
Overall Width: A + 7/8

Continuous Linear Slot Diffuser

F0 – Screw Holes in Margin

Duct Width: A + 7/16
Overall Width: A + 7/8

Mitered Corners

• 90-degree mitered corners are available as factory-fabricated section. Precise factory cutting and assembly reduces field fabrication time and assures proper fit. Corner sections are furnished and blanked off. Corner sections butt to adjacent straight sections, which are spliced together with aligning keys.
• Mitered corners are furnished in mounting style E2. When viewed from the room side, the mitered corner section appears identical to the butting straight sections.
• Plaster frame mitered corners can be specified with the outlet mitered corner.

How to Order

S [1] [2] [3] [4] [5] [6] [7]

[1] Type:

• 50 - 1/2' slot
• 75 - 3/4' slot
• 10 - 1' slot

[2] Number of Slots:

• 01-08 slots

[3] Mounting Style:

Continuous Slot Diffuser

• B0 - T-Bar Lay-in -Diffuser Only
• E0 - Diffuser Only
• E1 - Hanger Bracket
• E2 - Standard Mounting Frame
• F0 - Screw holes in margin

[4] Milter Type:

• C - Ceiling
• SI - Sidewall Inside
• SO - Sidewall Outside

[5] MC

[6] 90

[7] Finish

Continuous Linear Slot Diffuser

• CLR - Clear Anodized
• WHT - Bright White